全自動滅菌發酵罐1

概 述：工作體積15L,本發酵系統的材質、結構、布局*按照發酵系統設計，符合GMP標準。本系統配有所需的補料瓶、蠕動泵、循環泵、控制閥、管路系統、控制系統，充分保證系統的安全性、可靠性；還可配置空氣、蒸汽和水的預處理系統，在完成安裝調試后，只需接入蒸汽、空氣、水源和電源就可進行發酵運行。

罐體結構：主體材質為全不銹鋼，罐內*；帶發酵罐取樣、放料閥，移種管道。采用大視角罐內液位觀察 視鏡，12V安全視燈，帶有液位接口、接種口、補料口、及多個備用口，所有焊縫堅固整齊美觀。罐體及夾套的設計壓力均為0.3Mpa，采用優化導流設計，提高了交換效率和罐內溫度的均勻性，溫度的控制穩定均勻 是發酵得以成功的基本條件。

表面處理：內外拋光，且容易清洗，精度：0.4um。

滅菌方式：自動程序滅菌，滅菌過程可編程控制；可設置滅菌順序，范圍：100℃~130℃，氣動閥通過程序控制進行高溫滅菌。對于有些發酵品種對滅菌溫度要求波動很小,可降低勞動強度的可以選用自動程序控制滅菌，此時滅菌溫度非常精確

攪拌系統：采用直接耦合機械攪拌和罐頂式機械密封系統，以及英國機械密封(約翰克蘭)、高性能攪拌槳、消泡槳、交流調速電機，無級調速機, 可進行全自動控制。大功率的變速機構使攪拌穩定可保持運轉自如且不需要添加潤滑油，全自動設定控制范圍50～1000 rpm；

溫度自動控制系統：進水經過補水閥；電加熱，水冷卻，超溫保護功能，LCD觸摸屏控制；循環水加熱和冷卻系統；范圍：冷卻水溫度5~65℃；精度：±0.2℃；分辨率：0.01℃，配套制冷循環裝置，具有良好的熱交換效率；智能PID控制既保證了溫控的快速性又實現了節能。發酵溫度控制范圍：冷卻水溫度5~65℃, 精度：±0.1℃，溫度的精度和穩定對發酵的結果有著決定性的影響。

流量檢測與壓力檢測系統：轉子流量計檢測,手動控制空氣流量

pH自動控制：檢測pH，采用智能PID控制，蠕動泵自動添加酸、堿，精確控制pH（有手動、關閉、自動三檔可切換）。顯示范圍：0.00~14.00±0.01，全自動控制范圍：2.00~12.00±0.05。控制器可實現：pH值曲線分析、加酸、加堿量曲線分析、批報表分析、酸加入量累計顯示記錄、堿加入量累計顯示記錄、數據保存

DO在線檢測：可通過轉速、補料等進行聯動控制。智能PID控制，使溶解氧這個以往較難控制的參數，也達到了很理想的控制效果。控制范圍：0~150%±1%, 控制器可實現：DO值曲線分析、批報表分析（根據發酵時間，DO自動變量控制，至少10段）。

補料控制：具備完善的補料系統，補料可計量，可曲線記錄；蠕動泵數量可根據需要選擇，常規配置為每臺發酵罐二個。蠕動泵的作用可在控制界面上選擇設定，這樣使用戶在實際使用時更為方便靈活。配有特別設計的補料插針，以確保補料的安全操作。

Overview:Work volume of 15L, the material, structure and layout of the fermentation system are in full accordance with the fermentation system design, conforming to GMP standards.This system is equipped with required fill liu bottles, wriggle pump, circulating pump, the control valve and pipe system, control system, fully guarantee system of safety, reliability,configure pretreatment system of air, steam and water in complete installation debugging, after only access steam, air, water, and power source can be fermented operation.

Tank structure: Main material as a whole stainless steel, with no dead angle. Take special sampling, pick feeding valve, and the moveing microorganism pipeline. Adopted of observing endoscopic of big angle with tank level, safety depending on the lamp of 12V, with liquid level interface, vaccination mouth, filling material mouth, and multiple alternate mouth, all welds fortified tidy and beautiful. The design pressure of tanks and clip set are 0.3 Mpa, adopting the optimization diversion design, improved exchange efficiency and tank temperature uniformity, temperature control stability uniform is the basic conditions of fermentation to be successful.

Surface treatment: Internal and external polishing and easy cleaning, precision: 0.4um.

Sterilization mode: Automatic procedure sterilization, sterilization process programmable control. Can install sterilization sequence, the scope: 100 ℃ 130 ℃, pneumatic valve through procedure control on high temperature sterilizing. For some fermentation varieties to sterilization temperature requirements fluctuation, then reduce the labor intensity can choose automatic procedure control sterilization, now sterilization temperature is very precise.

Mixing system: Adopt direct coupling mechanical agitation and pot type mechanical seal system, and the British mechanical seal (John crowe LAN), high-performance agitator, defoaming OARS, exchange control motor, stepless speed regulation machine, can undertake full automatic control. High power shifting institutions make mixing stability can keep running freely, and do not need to add lubricating oil, automatic setting control range is of 50～1000rpm.

Automatic temperature control system:after filling water inlet valve. Electrical heating water cooling, overtemperature protection function, LCD touch screen control. Circulating water heating and cooling system. Scope: cooling water temperature of 5～65℃. Precision: ±0.2℃. Resolution: 0.01℃, supporting refrigeration device, with good heat efficiency. Intelligent PID control not only ensure the temperature control of the output and can save energy. The fermentation temperature control scope: The temperature of the cooling water 5～65 ℃, precision: ±0.1℃，the precision and stability of temperature of fermentation has a decisive influence on the result.

Flow test and stress test system: Rotor flowmeter test, manual control air flow.

PH automatic control: Detection pH, using intelligent PID control, wriggle pump automatically add acid, alkali, precise control pH (with manual and closed, automatic three gears can switch). Display range: 0.00～14.00±0.01，automatic control scope: 2.00～12.00±0.05. Controller can realize: PH value curve analysis, plus acid, add alkali amount curve analysis, batch statement analysis, acid addition amount accumulative total registering, alkali addition amount accumulative total display records, data storage.

DO online testing: By rotation speed, filling material for linkage control. Intelligent PID control, make this ever more difficult to control of dissolved parameters, also achieved very good controlling effect. Control scope: 0～150%±1%, Controller can realize: DO value curve analysis, batch statement analysis (according to fermentation time, DO automatic variables, control, at least 10 section).

Filling material control: With perfect fill material system, filling material will measure, can curve record. Peristaltic pump quantity can be choosed according to need. Conventional configured for each machine pick with two peristaltic pump. The role of peristaltic pump can be selected in the control interface, so that the user in actual use is more convenient. Equipped with special design of filling material insert needle, to ensure the safe operation of filling material.

全自動滅菌發酵罐1